<?xml version='1.0' encoding='UTF-8'?><KD_8_1_Z4 version="1" xmlns="http://www.brz.gv.at/eproc/kd/2018/12"><CONTRACTING_BODY><ADDRESS_CONTRACTING_BODY><OFFICIALNAME>Technische Universit&#228;t Wien</OFFICIALNAME><NATIONALID>9110007633536</NATIONALID><PHONE>+43 15880136689</PHONE><E_MAIL>ulrich.e366.schmid@tuwien.ac.at</E_MAIL><CONTACT>Univ.Prof. Dipl.-Phys. Dr.rer.nat. Ulrich Schmid</CONTACT></ADDRESS_CONTRACTING_BODY></CONTRACTING_BODY><OBJECT_CONTRACT><TITLE><P>Wafer Washer</P></TITLE> <REFERENCE_NUMBER>26300.02/027/2024</REFERENCE_NUMBER><CPV_MAIN><CPV_CODE CODE="24000000" /></CPV_MAIN><TYPE_CONTRACT CTYPE="SUPPLIES" /><SHORT_DESCR><P>Wafer Washer</P></SHORT_DESCR><NO_LOT_DIVISION /><OBJECT_DESCR><NUTS CODE="AT130" /></OBJECT_DESCR></OBJECT_CONTRACT><AWARD_CONTRACT><AWARDED_CONTRACT><CONTRACTOR><ADDRESS_CONTRACTOR><OFFICIALNAME>E V G r o u p E u r o p e &amp; A s i a / P a c i f i c G m b H</OFFICIALNAME></ADDRESS_CONTRACTOR></CONTRACTOR></AWARDED_CONTRACT></AWARD_CONTRACT><COMPLEMENTARY_INFO><DATE_DISPATCH_NOTICE>2024-05-22</DATE_DISPATCH_NOTICE></COMPLEMENTARY_INFO><ADDITIONAL_CORE_DATA><DATE_FIRST_PUBLICATION>2024-05-22</DATE_FIRST_PUBLICATION><DATETIME_LAST_CHANGE>2024-05-22T13:15:00</DATETIME_LAST_CHANGE><D_JUSTIFICATION><P>The Institute for Sensor and Actuator Systems (ISAS) is a university institute at the Faculty of Electrical Engineering and Information Technology of TU Wien, with a high research excellence in silicon microsystems technology. In order to master the challenges of this research field, state-of-the-art equipment for the realization of novel MEMS/NEMS (Micro/Nano Electro-Mechanical Systems) devices with structural dimensions from the micrometer to the nanometer range are a “condition sine qua non”. In order to secure and continue the ongoing research work at ISAS, an approximately 20-year-old wafer cleaning system has to be replaced by an equipment that meets the current technical requirements.</P><P>As future MEMS/NEMS activities at ISAS require the option for the new equipment of investigating wafer bond interfaces with an infrared station. In detail, the wafers are bonded with an existing wafer bonder at ISAS. Before wafer bonding, however, the surfaces of the wafers need to get prepared by the new equipment.</P><P></P><P>Key features of the equipment (must have):</P><P>• Max. outer equipment dimension:   H = 9970 mm B = 850 mm T = 1050 mm</P><P>• Automatic process software</P><P>• Automated recording of process and machine parameters</P><P>• Visualization of process parameters in a chart</P><P>• Spin drying up to 3000 rpm</P><P>• Polypropylene cleaning bowl (acetone use)</P><P>• Bowl wash functionality</P><P>• Spinner chuck for 100 mm with vacuum handling from bottom side</P><P>• Pre-aligner for vacuum chucks</P><P>• Spinner chuck for 5&quot;x5&quot; masks with mechanical fixture of substrate with pins in corners</P><P>• Megasonic cleaning nozzle for removal of microscopic particles</P><P>• DI-water dispense line</P><P>• Process support included</P><P>• Packing for transport included</P><P>• Transport expense to TU Wien included</P><P>• Transport insurance included</P><P>• Installation and acceptance included</P><P>• Operation training included</P><P>• Option for 2 additional chemistry lines with pressurized PFA tank for diluted chemistry</P><P>• Option infrared station for wafer bond defects for existing wafer bonder including PreBonding Station, Software evaluation of wafer bond defects on complete 4” wafer area</P><P></P><P></P><P></P><P></P><P>A study of available suppliers of wafer cleaners in the European Community was done most recently by the Institute of Sensor and Actuator Systems:</P><P>The following suppliers of wafer cleaner systems could be found: Suss, EVG, Osiris International GmbH, amcoss GmbH.</P><P>Only EVG is fulfilling necessities in tender above, especial the infrared station for wafer bond defects and chemistry lines will be a key equipment in a planned project and will be financed as well as upgraded in the frame of this planned project. These features can only be supplied by EVG especially because the PreBonding Station of the device is working with equipment parts of an existing  EVG 501 wafer bonder.</P></D_JUSTIFICATION></ADDITIONAL_CORE_DATA></KD_8_1_Z4>